| General Technical |
| Input/Output frequency range |
400MHz to 7300 MHz |
| IF bandwidth |
180 MHz |
| Input power range |
+30 dBm peak (+25 dBm average) |
| Output power range(CW) (RF-A1 to RF-B4) |
0 to -100 dBm |
| Input power accuracy |
Specification: ±0.5 dB (+25 to -40 dBm) |
| Typical: ±0.3 dB (+25 to -40 dBm) |
| Output power accuracy(RF-A1 to RF-B4) |
Specification: |
±0.75 dB ( 0 to -90 dBm)
±1.50 dB ( -90 to -100 dBm) |
| Typical: |
±0.50 dB ( 0 to -90 dBm)
±1.00 dB ( -90 to -100 dBm) |
| Signal to noise ratio |
Specification: |
≥60 dB ( 100 KHz RBW), power level -10 dBm |
| Typical: |
≥70 dB ( 100 KHz RBW), power level -10 dBm |
| Input/Output return |
Specification: >13 dB |
| Spurious (signal applied) |
< -70 dBc (CW, for signal levels greater than -10 dBm) |
| Inherent spurious floor (no signal) |
≤ -95 dBm（100 KHz RBW） |
| Quantization |
14 bits |
| Noise figure |
≤ 26 dB at minimum input attenuation |
| Sampling data rate |
30, 60, 120, 240 Msps |
| Spectral flatness |
Specification: ≤±0.75 dB ( ±80 MHz) |
| Typical: ±0.5 dB ( ±80 MHz) |
| Port to Port Isolation |
> 110 dB typical |
| WLAN (802.11a/b/g/n/p/ac/ax) |
| EVM |
Residual VSA EVM
(full packet channel estimation):
(measured at -10 dBm)
|
≤-47 dB for 20 M（typical: -50 dB）
≤-47 dB for 40 M（typical: -50 dB）
≤-46 dB for 80 M（typical: -48 dB）
≤-45 dB for 160 M（typical: -47dB） |
|
Residual VSG EVM:
(full packet channel estimation):
(measured at -10 dBm)
|
≤-48 dB for 20 M（typical: -50 dB）
≤-48 dB for 40 M（typical: -50 dB）
≤-46 dB for 80 M（typical: -48 dB）
≤-45 dB for 160 M（typical: -47 dB） |
| Peak power |
VSA power accuracy: ±0.5 dB (+20 to -45 dBm) |
| RMS power |
| Frequency error |
VSA measurement error: ≤±0.2 ppm calibrated |
| RMS phase noise |
VSA integrated phase noise: <0.3 degrees (100 Hz to 1 MHz) |
| Spectral mask |
Spectral mask view: ±90 MHz |
| Spectral flatness |
VSA flatness over 160 MHz BW: ±0.75 dB |
| CCDF (complementary cumulative distribution function) |
Probability of peak signal power being greater than a given power level versus peak-to-average power ratio (dB) |
| Bluetooth®(1.0/2.0/2.1/3.0/4.0/4.1/4.2/5.0)BLE |
| TX output power |
VSA power accuracy: ±0.5 dB (+20 to -45 dBm) |
| TX output spectrum |
| Modulation characteristics |
(For EVM better than -25 dB) VSA measurement error:≤± 0.2 ppm calibrated |
| Carrier frequency tolerance |
| Carrier frequency drift |
| RMS EVM (EDR) |
Residual VSA EVM: ≤-35 dB (+20 to -30 dBm) Residual VSG EVM: ≤-35 dB (-10 to -70 dBm) |
| Peak EVM (EDR) |
